There Are A Few Reasons That People Can Succeed In The Double Glazing Door Lock Repairs Industry

There Are A Few Reasons That People Can Succeed In The Double Glazing Door Lock Repairs Industry

Double Glazing Door Lock Repairs

Have your uPVC window or door mechanism started to fail? Perhaps the window or door handles aren't able to connect correctly or are difficult to use.

You will lose energy if your double-glazed doors don't perform as they should. This also increases the risk of burglary. Owen the Locksmith can fix your door lock at an affordable cost.

Snapped Key

When a key snaps off within a lock, it could be incredibly frustrating. It could also be a security risk since the door may not be locked and leave you open to intrusion. There are a few easy fixes you can make to fix the problem and make your door work again.

Be sure to remain calm. If you panic and start poking around wildly, you might just end up pushing the broken piece of the key even further into the lock, which could make the situation worse.

Then, spray WD-40 or another penetrating oil into the lock to make the broken piece slide out more easily. You can also use a screwdriver to break off any pieces stuck. If you happen to have a small piece of the key visible, you can make use of a paperclip or other metal object that is thin to grab it and pull it out. Both methods work, but be very careful not to push the broken piece of the key deeper into the keyway.

Some paperclips have grooved edges that can serve to extract hooks and some Jigsaw blades can also be used for this use. If you don't happen to have any of these items then you can bend a hook using needle-nosed pliers. You can also use a pair tweezers to grasp and pull out the remaining pieces of broken keys.

If you are unable to remove the broken key piece, use a lock deicer. It is available at most hardware stores. It is used to freeze any water or ice that could be inside the lock.

If none of these solutions work, it might be time to consult a locksmith. Fitlocks experts can fix issues such as broken handles and broken keys with uPVC locks and door mechanisms. They can also modify your double glazing door mechanisms to make them easier to operate. Book a double glazing repair with us online or give us a phone call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose an extremely risky security issue. A professional locksmith can easily fix the cylinder. To fix the cylinder a locksmith will need to tap it. They can do this with an hammer or another tools, but the most effective way is to employ a long match or a piece of wire. Place the match or wire end near the keyway. The locksmith will strike the lock and break it open. This is much better than using a hammer that could cause damage to the lock.

Overheating is the primary reason for cylinder heads to crack. This can occur when the block and the cylinder head are made of different metals like cast-iron and aluminum. Different metals can heat up and cool off at different rates. This could cause localized hotspots to expand faster than the rest of the cylinder.

Another possible cause of cylinder cracks is corrosion. If the head and block of the cylinder are not maintained in a timely manner they could rust or corrode and cause them to expand faster than expected. In time, this could cause cracks.

If your uPVC window or door lock is stiff and requires a lot of pressure to turn, it could be due to a variety reasons. A malfunctioning locking mechanism, misalignment or an old handle are the most common causes of this problem.

It is a quick and inexpensive fix that most homeowners with double glazing can perform. A professional locksmith will usually solve the issue within one hour of arriving at the property. Depending on your needs they can change the locking mechanism, change the window handles, and change the gearboxes. A professional locksmith will always be able to advise you on the most cost-effective solution for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders, which give you an extra security layer from burglars. It is a small cost to enjoy the peace of mind that comes from knowing that your uPVC door is secure.

Broken Handle

Window handle locks have intricate mechanisms that wear out with age and usage, so it's no surprise that they can break. It isn't always easy to pinpoint the cause of the problem and then fix it properly.

The issue could be related to the locking mechanism inside or the latch, repairing your broken handle will improve your uPVC double glazing door's security and allow you to stop drafts. It is costly to replace or repair your handle incorrectly and it can also harm the frame and the lock of your door.

With the window in the open position and the window open, loosen the screw that secures the handle using a screwdriver. The screw should be located on the inside of the backplate, which is usually concealed by a screw cap for aesthetic purposes. Be sure not to lose any internal parts within the handle, like the levers or plates on the opposite side of the spindle. Ideally, keep them in the same place so you can replace them again in the event of a need.

Then, using another screwdriver loosen the screw that connects the handle with the spindle at the back. Once the screw is released, you'll be capable of pulling the handle off and pull off the damaged spindle. Replace it with a new spindle, ensuring it's the same length (you can purchase them online or at hardware stores). Screw it in the correct position. Do not overtighten the screw because this could damage the handle and the window frame.

Make sure the new handle is correctly installed after which you can close and test the handle. It should operate smoothly and you'll be able open your window once again.


While you're working on the handle, don't forget to make sure your uPVC windows are closing properly. If they're not closing properly, you could experience damp or draughts inside your home. You could also compromise the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges of the frames of your windows to ensure that they close correctly.

Broken Spindle

It is more common for the spindle to break than the handle. This is particularly frequent in uPVC tilt and turn windows. These kinds of windows require a handle which is a lock mechanism that is located in the frame of the window. The handle is attached to a centre rod that in turn activates cams that look like mushrooms, they locks are inserted into the window frame. If the dead latch mechanism fails to open when the handle is turned, it is most likely the spindle is broken. This can be a frustrating issue.

Fortunately there are steps that can be taken to rectify this issue.  double glazing repairs near me  will be able to quickly and efficiently repair this problem. They can disassemble the window handle by using a tool that removes the wheel portion of the mechanism that is where the spindle is. This can be done with no damage to the handle or the window frame.

After removing the wheel, the technician can examine the spindle and identify the reason for its break. This involves breaking down the spindle into its component parts and carefully recording their general condition as well as any specific areas of damage or excessive wear. This process is usually carried out by technicians in a clean environment.

Then, clean the damaged spindle. This will help remove any dirt or other debris that might be preventing it from functioning normally. After that, the spindle could be repaired or replaced. If the technician is replacing the spindle he can use a dowel that is comparable in size to the original. Then, he will make holes in the same way into both pieces. This will ensure that the spindle fits perfectly with the handle.

If the damaged spindle can't be repaired, it might require replacement. Home centers can sell generic replacements, but if your window design is unusual you'll need to contact an expert in woodworking or cabinet making who can recreate the exact piece. Once the new spindle is installed, it can be attached to the handle by line up the holes for screws in the handle with the frames existing screws. Once the new handle is firmly in place, you'll be able to operate your uPVC window.